DynamicLift™ Remote Operated Magnet
The remote operated DynamicLift™ permanent lift magnet, featuring Magswitch® technology (E50 – 900/660 CE), can be turned “on” or “off” using a remote control, without the need of air or electricity! Not only does this give the operator freedom from electrical cords and air hoses, but also opens up a whole new range of lifting possibilities where accessibility to the magnet was cumbersome or impossible to reach, such as lifting above or below arm’s length, into deep channels, loading or unloading CNC/cutting tables and operation from inside the forklift.
Remote Operated, DynamicLift™ (DLR0600) – featured at AWRF’s 2013 Product and Information Exhibition
This compact, yet powerful, Rare Earth lift magnet contains an internal on/off release device that does not contact or damage the surface of the part being lifted. Permanent magnetic lifts also eliminate the fear of dropping the load being lifted due to power failures.
- Remote Operated, locking, On/Off Rare Earth permanent magnet will stay “on” if battery loses power
- Operates magnets up to 10 meters (32.8 feet) away
- Built in safety – a load sensor and a 3-button power off sequence prevent accidental release while under load
- Indicator lights for magnet operational state and battery strength
- Includes two, 12 volt rechargeable, Lithium-ion batteries (200 cycles per charge) and charger
- Secondary manual release in case of battery failure
- 3:1 Design Factor
- Heat resistant up to 180°F (82°C)
- ASME B30.20 BHT-1 Design Category B Service Class 3
Literature Download: DynamicLift™ Remote Operated Magnet
| Rare Earth DynamicLift™ Magnets | |||||||||||
| Lift | Overall | Magnet | Bail | ||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|
| Model No. | LBS | Ht. (in) | Wd. (in) | Ln. (in) | Wt. | Ht. (in) | Wd. (in) | Ln. (in) | Th. (in) | Ht. (in) | Wd. (in) |
| DLR0600 | 600 | 12-1/2 | 4 | 8-1/2 | 20 | 4 | 2-3/4 | 6-1/2 | 3/8 | 2-1/2 | 3-1/4 |
| Lifting Value in lbs & *Maximum Sheet Length Due To Sag For Material Thickness For Single Magnet Use | |||||||
| Flat/Sheet Lifting Applications | |||||||
|---|---|---|---|---|---|---|---|
| Model No. | 1/4″(6′ Lg) | 3/8″(8′ Lg) | 1/2″(8′ Lg) | 3/4″(8′ Lg) | 1″(10’Lg) | 2″(10′ Lg) | 3″(10′ Lg) |
| DLR0600 | 368 (166) | 475 (215) | 550 (249) | 575 (260) | 600 (272) | 600 (272) | 600 (272 |
|
Lifting Values for the DynamicLift™ Magnets are stated at 33% of the actual value. We recommend when lifting sheets over 8′, use 2 or more lifts on a spreader bar to prevent sheet flexing, sagging or peel-off. Thin material is susceptible to magnetic bleed through, resulting in two sheets being lifted at once. Consult the factory before specifying these magnets for use on round materials. *Max. sheet lengths are selected due to sag characteristics of specified sheet. The item to be lifted must cover the entire length and width of the magnetic poles to properly engage and release the part. CF = Consult Factory, NA = Not Applicable (Magnets will not turn “ON” with stated thicknesses.)
|
|||||||
Note: Never stand under load being lifted. Always use extra caution. Only use magnetic lifts on material that does not flex or bend. The surface of the lift, and the load being lifted, need to be clean and free of chips, oil, slag, dirt, etc. Lifting magnets must be centered on load. Not recommended for parts that are round, painted or have finish coated surfaces.