Universal – For lifting in any direction

The type IP10 vertical lifting clamp is used for lifting, turning (180°) and vertical transfer of steel plates and constructions. All IP10 clamps are built with a latch that locks in both the open and closed positions. This allows the operator to easily position the clamp, close the latch and move away from the load before the lift begins. IP10 clamps with working load limits of 12 tons and up have special hook-up devices built in to assist in the placement of these large-sized clamps. To avoid overloading your clamp please refer to figures 1 and 2. Higher working load limits and different jaw apertures are available upon request.

The new basic type IP10 is an innovation based on the familiar ‘IPZ’ lifting clamps. The new models have a larger jaw opening, which makes it possible to lift plates with very different thickness by using one and the same clamp. For special applications see also IPU10, IP(U)10/s IP(U)10/H, IPNM and Custom Designed Clamps.

 

 
Spare parts for IPU10 lifting
clamps:		 Order No.
1. body complete  
2. universal hoisting eye complete 1235
3. camsegment complete 1234
4. latch complete 1233
5. spring for latch complete 1063
6. camsegment shaft complete 1046
7. hoisting eye shaft complete 1047
10. pivot complete (round) 0098
10. pivot complete (oval) 0099
Before using the clamp always read the Operator’s manual supplied with the clamp.
Model Order
No. 		WLL
per pce
in t 		Weight
per pce
lbs
0,5-IP10 1674 0.5 4.0
1-IP10 1662 1.0 4.4
2-IP10 1676 2.0 15.0
3-IP10 1664 3.0 30.4
4,5-IP10 1666 4.5 33.0
6-IP10 1668 6.0 51.8
9-IP10 1670 9.0 60.6
9-IP10/J 1672 9.0 62.8
12-IP10 1678 12.0 108.0
12-IP10/J 1680 12.0 128.0
16-IP10 1682 16.0 150.0
16-IP10/J 1684 16.0 200.0
22,5-IP10 1686 22.5 238.0
22,5-IP10/J 1688 22.5 243.0
30-IP10 1690 30.0 326.0
30-IP10/J 1692 30.0 335.0
     
        Fig. 1   Fig. 2

Model Order No. WLL per pce in t Jaw A Dimensions in Inches Weight per pce lbs
B C D E F G H J K
0,5-IP10 1674 0.5 0-5/58 1 47/64 5 3/64 8 5/32 1 3/16 4 17/32 1 39/64 1 7/64 – 25/64 4.0
1-IP10 1662 1.0 0-3/4 1 3/4 5 15/32 8 15/32 1 3/16 4 15/32 1 58 1 1/2 – 25/64 4.4
2-IP10 1676 2.0 0-1 3/8 3 5/64 7 29/32 13 15/64 2 3/4 7 15/32 2 13/32 2 11/64 – 5/8 15.0
3-IP10 1664 3.0 0-1 5/8 3 15/16 9 61/64 17 11/64 2 61/64 8 55/64 3 5/64 2 23/64 – 25/32 30.4
4,5-IP10 1666 4.5 0-1 5/8 3 15/16 9 61/64 17 11/64 2 61/64 8 55/64 3 15/64 2 9/16 – 25/32 33.0
6-IP10 1668 6.0 0-2 4 61/64 11 57/64 20 9/32 3 5/32 11 1/2 3 5/16 3 47/64 1 37/64 25/32 51.8
9-IP10 1670 9.0 0-2 4 61/64 12 51/64 21 21/32 3 5/32 12 13/64 3 5/8 4 9/64 1 47/64 1 60.6
9-IP10/J 1672 9.0 2-3 7/8 4 61/64 12 51/64 21 27/32 3 5/32 14 11/64 3 5/8 4 9/64 1 47/64 1 62.8
12-IP10 1678 12.0 0-2 1/8 6 19/64 15 25/64 22 53/64 3 5/32 13 1/32 4 39/64 5 25/64 1 39/64 1 108.0
12-IP10/J 1680 12.0 2 1/8-4 1/4 7 1/64 17 9/32 24 51/64 3 5/32 16 11/32 4 3964 5 25/64 1 39/64 1 128.0
16-IP10 1682 16.0 1/4-2 1/2 7 1/64 18 5/16 27 11/64 3 15/32 15 5/8 4 11/16 6 1/32 1 59/64 1 150.0
16-IP10/J 1684 16.0 2 1/2-5 8 3/16 20 33/64 29 3/8 3 15/32 18 37/64 4 11/16 6 11/32 1 59/64 1 200.0
22,5-IP10 1686 22.5 1/4-3 1/8 8 47/64 21 13/16 31 1/2 4 21/64 18 1/2 5 29/64 7 21/64 1 59/64 1 238.0
22,5-IP10/J 1688 22.5 3 1/8-6 1/8 9 61/64 24 23/32 34 41/64 4 21/64 22 41/64 5 23/64 7 23/32 1 59/64 1 243.0
30-IP10 1690 30.0 1/4-3 1/8 8 47/64 21 29/64 31 1/2 4 21/64 18 1/2 5 63/64 7 21/64 2 1/8 1 3/16 326.0
30-IP10/J 1692 30.0 3 1/8-6 1/8 9 27/32 24 13/32 34 41/64 4 21/64 22 1/4 5 63/64 7 23/32 2 1/8 1 3/16 335.0