Twin-Path Bridle Slings with K-Spec core yarns
Twin-Path® Bridle Slings TPXC, K-Spec yarn
with green Covermax cover and RIGGER’S CHOICE® Connectors
DF 5:1
Depending on sling size we either use standard round- or flat bottom connectors. Sling information tag with serial numbers and other important information is attached. |
Capacity tag with all ASME required sling angles. |
Sling legs are clearly identified for use in a bridle sling configuration and incorporate our Check-Fast® Inspection System. |
Note that the minimum end-fitting capacity must be equal or higher than the VERTICAL (90°) SINGLE leg capacity. See table below.
The variety of end fitting choice is astronomical, so please select Rigger’s Choice®, Crosby®, Green Pin® or any other Hardware as an end fitting.
When selecting hardware remember that a DF 5:1 is required, means any CHAIN hardware WLL has to be converted from 4:1 to 5:1.
Note that 1- and 2 leg slings are made with Rigger’s Choice® Master Links, and 3-and 4-leg slings are made with Rigger’s Choice® Master Link Sub-Assemblies. Other links (Crosby, CM, Gunnebo, etc.) are available upon request.
All slings are connected to Master links or Sub-Links with Rigger’s Choice® Web-Connector Code No. C8-WSC-xxx-RC.
Twin-Path® Extra Bridle Slings K-SPEC® Core Yarns | |||||||
---|---|---|---|---|---|---|---|
Bridle WLL to the Horizontal Angle | |||||||
WLL lbs. 60° | WLL lbs. 45° | WLL lbs. 30° | Nom. Top Link Type C-10 diameter inch | Min. Sling Length w/o hardware | |||
TPXC 2000-A1 | 1-leg | 20,000* | — | — | 1 | 3 | |
TPXC 2500-A1 | 1-leg | 25,000* | — | — | 1-1/4 | 3 | |
TPXC 3000-A1 | 1-leg | 30,000* | — | — | 1-1/4 | 3 | |
TPXC 4000-A1 | 1-leg | 40,000* | — | — | 1-1/2 | 4 | |
TPXC 5000-A1 | 1-leg | 50,000* | — | — | 1-1/2 | 4 | |
TPXC 6000-A1 | 1-leg | 57,800* | — | — | 1-3/4 | 4 | |
TPXC 2000-A2 | 2-leg | 34,640 | 28,285 | 20,000 | 1-1/4 | 3 | |
TPXC 2500-A2 | 2-leg | 43,300 | 35,360 | 25,000 | 1-1/2 | 3 | |
TPXC 3000-A2 | 2-leg | 51,960 | 42,430 | 30,000 | 1-1/2 | 3 | |
TPXC 4000-A2 | 2-leg | 69,280 | 56,570 | 40,000 | 1-3/4 | 4 | |
TPXC 5000-A2 | 2-leg | 86,600 | 70,710 | 50,000 | 2 | 4 | |
TPXC 6000-A2 | 2-leg | 100,100 | 81,730 | 57,800 | 2 | 4 | |
TPXC 2000-A3 | 3-leg | 51,962 | 42,430 | 30,000 | 1-1/2 | 3 | |
TPXC 2500-A3 | 3-leg | 64,950 | 53,050 | 37,500 | 1-3/4 | 3 | |
TPXC 3000-A3 | 3-leg | 77,940 | 63,650 | 45,000 | 1-3/4 | 3 | |
TPXC 4000-A3 | 3-leg | 103,920 | 84,850 |
60,000 |
2-1/4 | 4 | |
TPXC 5000-A3 | 3-leg | 129,900 | 106,000 | 75,000 | 2-1/4 | 4 | |
TPXC 6000-A3 | 3-leg | 150,160 | 122,600 | 86,700 | 2-1/2 | 4 | |
TPXC 2000-A4 | 4-leg | 69,300 | 56,570 | 40,000 | 1-3/4 | 3 | |
TPXC 2500-A4 | 4-leg | 86,600 | 70,700 | 50,000 | 2 | 3 | |
TPXC 3000-A4 | 4-leg | 103,920 | 84,850 | 60,000 | 2-1/4 | 3 | |
TPXC 4000-A4 | 4-leg | 138,560 | 113,130 | 80,000 | 2-1/4 | 4 | |
TPXC 5000-A4 | 4-leg | 173,200 | 141,420 | 100,000 | 3 | 4 | |
TPXC 6000-A4 | 4-leg | 200,220 | 163,480 | 115,600 | 3 | 4 | |
* Capacity at 90° |
Select RIGGER’S CHOICE® and Crosby Hardware from Page 100-105.
Rigger’s Choice® fittings are attached the same as grade 80 chain fittings. Tools are required to connect and disconnect the fittings. This is regarded as a more permanent connection.